terminal cable

In order to solve the problems of traditional design method of relay control circuit system, a method to generate the electrical device terminal array and cable list is proposed.

继电线路的可测性设计和功能验证，在电力系统的安全可靠性运行中起着重要的作用，用逻辑分析的方法对控制电路进行功能验证是一种全新的思路。

Both the narrow pulses and the steep front pulses are applied to the initial terminal of the XLPE cable respectively, and the oscillograms at both terminals are simultaneously recorded using a digital oscilloscope.

在两段不同长度的电缆首端分别注入窄脉冲和陡前沿脉冲，同时记录首末端波形；

Injecting impulse current at the terminal of power cable into the hybrid transmission line to be detected and conducting multi-resolution analysis of injected sampling signal by wavelet analysis, the position of modular maximum point of sampling signal is obtained.

向待测混合线路的电缆端注入脉冲电流，利用小波分析对注入的采样信号进行多分辨分析，得到模极大值点的位置。

In this way, the'contact point-sampling-contact point'access mode of the wiring terminal of the primary cable is changed to be the'sampling-contact point-contact point'mode.

这样，将一次电缆接线端子接入方式由现有的“接点―采样―接点”方式改进为“采样―接点―接点”方式。

Connectors, Backshells , Terminal Block , Cable Support, Contacts, Wire , Conduits, Circuit Breakers, Relays, Switches, Tools, Other.

连接器 、 后盖 、 接线盒 、 电缆支撑系统 、 接触 、 电线 、 导管 、 断路开关 、 继电器 、 开关 、 工具以及其它.

Connect cable F of cable TV/ user connector to the terminal of cable input.

将有线电视电缆F/用户接头接入本机“电缆输入”端。

The terminal fittings on the cable are standard bearing sockets.

钢索的端部连接采用标准承压锚杯.

Analysis on 10 kV Cable Outdoor Wiring Terminal Fault& its Prevention Measure

10kV电缆户外接线端子故障分析及防范措施

Cable Modem is the terminal device of HFC broadband access network.

CABLE Modem就是HFC宽带接入网的用户端设备。

Terminal Board cable connection for quick replacement of the cap/ cable assembly

接线端子板的电缆连接方式，便于电缆的迅速装配和更换

Using VB6.0 as development tool, ACL-7225 data sampling cards and industry computer, the auto-control system on decorticating, truncating, setting terminal and length of cable is studied and produced.

本文介绍了应用VB6.0作为开发工具，利用工控机和ACL-7225数据采集卡，开发自动控制系统的方法。

Secondly, a online cable fault location in single terminal for mine supply line is proposed based on wavelet transform muti-resolution analysis of transient traveling wave in partial mutation and weak variation signal processing is stated.

然后根据小波对局部突变信号或者微弱变化信号处理上的优势，利用小波变换对暂态行波进行多分辨率分析，从而提出了一种针对矿用供电线路的电缆故障的单端行波在线测距算法。

Causes Analysis of Burning Accidents of Indoor Terminal of Cross-linked Cable with Single Core

单芯交联电缆户内终端烧毁事故的分析

Study on the On line Detecting Technique for Power Cable and Terminal Based on Heat Effect

基于热效应的电力电缆及其终端在线检测技术

Therefore it is required to develop a kind of Home Integrated Service Terminal with embedded cable modem, to realize high speed interaction of multimedia services.

因此，需要研制使用内嵌CM技术的家用综合业务终端，来完成高速多媒体业务的交互。

Megohm inspection method is to form an electric cable terminal at the online access, another access terminal on the motor casing, megohm shake table to observe the value of insulation resistance.

检查方法是将兆欧表上的一个接线柱接在电泵电缆线上，另一接线柱接在电机外壳上，摇动兆欧表，观察绝缘电阻值。

The temperature data acquisition terminal for cable is an important part of the Temperature Monitoring System for Underground Cable Junction of Urban Distribution Network, which needs to perform acquisition, processing, saving and wireless transmission of the temperature data.

电缆温度采集终端是城市配电网地下电缆接头温度巡测系统的重要组成部分，负责电缆接头温度的采集、处理、保存和无线传输。

By using the methods, the electrical device terminal array and cable list can be generated automatically, meanwhile, the design result is optimized.

在此基础上，实现了设备端子排和电缆表的自动生成，并对设计结果进行了优化。

The voltage at motor terminal would be double because of the effects of cable distributed parameters when motor is fed with PWM inverter through a long cable therefore resulting in a heavy stress on motor.

PWM逆变器通过长线电缆与电机连接时，由于电缆分布参数的影响会在电机端产生2倍的过电压，从而使电机承受的应力大为增加。

Based on the fact that electric power is output from the HF terminal of the frequency converter, this paper analyzes the causes and harms of higher harmonics, as well as the reasons for the power cable oscillation radiation during transmission and their solutions.

根据变频系统高频输出电能特点，分析高次谐波产生原因和危害，并给出在电力电缆传输过程中产生振荡辐射的原因和解决方法。